browse
tx R/C Systems Tx Rx etc tx ARTF and Kits wat Servosmot Electric Motors & Accessories esc Speed Controllers (ESC's) rx Receiver NiMH Battery Packs lipo Lipo Packs & Accessories charger Chargers & Charging Accs wat Watt Meters, Checkers, etc wat UBECS & Regulators rx I.C. Glow and Petrol Engines plug I.C. Engine Accessories starter Field Equipment starter Cases and Bags prop Propellers & Accessories lipo Spinners wheel Wheels and Undercarriages spinner Connectors spinner Extension and Y Leads spinner Switches clevis Fittings (Horns, Hinge Etc) spinner Nuts, Bolts, Screws etc spinner Scale Accessories balsa Building Materials - Balsa etc cover Covering Materials spinner Simulators brush Brushes brush Pilot Figures band Ties, Tapes, Bands etc wire Heat Shrink & Wire toolTools glue Adhesives/Fillers etc. dope Dopes, Sealers, Proofers etc dope Paints
Multiplex Multigyro G3 3-Axis Gyro
thumb tumb
 
£

 

 

Quantity: 

e MULTIGyro G3 has been developed specifically for RC fixed-wing model aircraft, and automatically stabilises the model, and what's more is suitable for all modern R/C systems - not just Multiplex!

You instantly fly more accurately and safely!

 

The model's familiar flying characteristics are virtually unchanged, but it flies much more smoothly, more precisely, and is less susceptible to weather-induced and aerodynamic influences.

 

The triple-axis stabilisation system is suitable for all current types of fixed-wing aircraft, including:

normal aeroplanes, V-tail, delta / flying wing.

 

A special feature of the MULTIGyro G3 is its three modes of operation. The gyro can be switched between OFF, Normal (damping) and Heading-Hold (stabilisation) from the transmitter using a vacant channel. Normal mode virtually eradicates the effect of wind and turbulence on the model (wind eliminator), whereas Heading-Hold mode enables the model to maintain the last commanded flight attitude until the pilot gives a further control command.

Torque-rolls and hovering become child's play - provided that motor power is sufficient.

Gyro gain can be adjusted separately for each primary axis (elevator, rudder and aileron) on the device itself. In this way the model can be set up accurately to suit your preference.

Installing the MULTIGyro G3 could hardly be simpler, and only takes a few mintues.

Set contents: MULTIGyro G3, 2 self-adhesive pads, 4 connecting leads, 5-language instructions

 

Features

bullet Triple-axis gyro system, specifically for RC fixed-wing model aircraft

bullet Suitable for all current RC systems

bullet Selectable model type: standard fixed-wing, delta or flying wing, V-tail

bullet Modes switchable at the transmitter (OFF, normal, heading-hold)

bullet Variable gyro gain, individual and without PC

bullet Small and light (47 x 33 x 14 mm, 11 g)

 

Specifications

bullet Operating voltage 5 - 6 Volt
bullet Servo signal frame rate 50 Hz / 20 ms
bullet Servo signal 1520 ±500 μs
bullet Pulse width limits 970~2070 μs
bullet Gyro sensing rate 1 KHz
bullet Operating temperature -40°C to 85°C
bullet Dimensions 47 x 33 x 14 mm
bullet Weight 11 g
bullet Supported model types Fixed-wing aircraft, V-tail, delta / flying wing
bullet Modes 1. Off / 2. Normal / 3. Heading-hold; switchable at the transmitter

 

 

 

 

 

Download the manual!

Click the image on the left to download the full manual for the Multiplex Cockpit SX Range (Multi-Language)

There is lots of useful extra information on this superb radio.

 


 

 


 


Home I Terms & Privacy Policy I Contact